Product Catalogue

Excel Series 40 - 2" thru 60" for High Temperature & Dirty Service 125/150 lb. Flanging*

Download this page only in PDF format
Download Excel Series 40 Section in PDF format

 

Please choose:


Typical Dimensions: 2" through 14"



2" through 14"
Size A B C D E F H Max.
ΔP
Approx.
Wt. (LB.)
2" 2 5-3/8 5-3/8 1-1/2 3-7/8 4-1/4 1/2 150 9lbs
2-1/2" 2-1/2" 5-5/8 5-5/8 1-1/2 4-5/8 4-1/4 1/2 150 10lbs
3" 3" 5-7/8 5-7/8 1-1/2 5-1/8 4-1/4 1/2 150 11lbs
4" 4" 6-3/8 6-3/8 1-1/2 6-3/8 4-1/4 1/2 125 12lbs
5" 5" 6-7/8 6-7/8 1-1/2 7-1/2 4-1/4 1/2 100 15lbs
6" 6" 7-3/8 7-3/8 1-1/2 8-1/2 4-1/4 1/2 80 17lbs
8" 8" 9-5/8 9-5/8 1-7/8 10-3/4 5-1/8 3/4 90 32lbs
10" 10" 10-5/8 10-5/8 1-7/8 13 5-1/8 3/4 70 40lbs
12" 12" 11-5/8 11-5/8 1-7/8 15-1/4 5-1/8 3/4 50 50lbs
14" 13-1/8 12-1/8 12-1/8 1-7/8 16-3/8 5-1/8 3/4 30 70lbs

Typical Dimensions: 16" thru 24"

16" thru 24"
Size A B C D E F H Max ΔP Approx Wt. (Lb.)
16" 15-1/8 14-1/2 14-1/2 2-3/8 18-1/4 5-1/8 1 40 122#
18" 17-1/8 15-1/2 15-1/2 2-3/8 20-3/4 5-1/8 1 30 155#
20" 19-1/8 16-1/2 16-1/2 2-3/8 22-3/4 5-1/8 1 25 192#
22" 21-1/8 17-1/2 17-1/2 2-3/8 25 5-1/8 1 20 232#
24" 23-1/8 18-1/2 18-1/2 2-3/8 27 5-1/8 1 17 276#

Typical Dimensions: 26" thru 60"


Alignment holes shown match ANSI 125/150 lb. flange bolt circle and number of holes. On valves 32" and larger, the diameter of the holes adjacent the shaft on both ends, match ANSI 25/AWWA C207B.


26" (660.4 mm) thru 60" (1524 mm)
Size A B C D E F H K Max.
Δ P
Approx.
Wt. (Lb.)
26" 25-1/8 21 21 2-3/4 29 5-1/8 1-1/4 - 14 324#
28" 27-1/8 22 22 2-3/4 31 5-1/8 1-1/4 - 12 376#
30" 29-1/8 23 23 2-3/4 33-1/2 5-1/8 1-1/4 - 11 432#
32" 31 25 25 3-1/4 35-1/2 7 1-1/2 1-3/8 12 512#
34" 33 26 26 3-1/4 37-1/2 7 1-1/2 1-3/8 10 578#
36" 35 27 27 3-1/4 40 7 1-1/2 1-3/8 9 648#
38" 37 28 28 3-1/4 42-3/4 7 1-1/2 1-3/8 8 722#
40" 39 30-1/4 30-1/4 4 44-3/4 7 1-3/4 2 9 888#
42" 41 31-1/4 31-1/4 4 46-3/4 7 1-3/4 2 8 970#
44" 43 32-1/4 32-1/4 4 49-1/2 7 1-3/4 2 7 970#
46" 45 33-1/4 33-1/4 4 51-1/2 7 1-3/4 2 6 1163#
48" 47 34-1/4 34-1/4 4 53-3/4 7 1-3/4 2 5 1267#
54" 53 37 37 6 60-1/4 10 2 2 5 1840#
60" 59 40 40 7 66-3/4 10 2-1/4 2-1/2 5 2600#

* "G" Length and configuration of the shaft end will vary to accommodate specific actuators. Refer to the accessory section for typical flatted, keywayed, and hexed end configurations available.

MAX. ΔP is based on 0° disc position, using standard materials of construction at a maximum temperature of 450° Fahrenheit.
Consult factory for MAX. ΔP for elevated temperatures.

Process Development & Control, Inc. reserves the right to make design improvements and/or change dimensions without notice.

Additional Information